[sisyphus] Принтер Canon LBP2900

Astakhov Andrey astakhov.andrey на gmail.com
Вт Апр 10 19:42:46 MSD 2007

Ставил драйвер для сабжа, следовал инструкции которая идет с драйверами 
(взято с сайта Canon). Инструкция вот:

The printer driver must be installed in order to print from Canon 
printers using Linux.
The printer driver files to be installed consist of:

    * cndrvcups-capt-1.3x-x.i386.rpm : rpm file of the CAPT printer
      driver module

    * cndrvcups-common-1.3x-x.i386.rpm : rpm file of a common module for
      CUPS drivers


    * The files names of the CUPS driver common module and the printer
      driver module described in this procedure differ depending on the
      installed driver version. The "1.3x-x" part of the file name
      indicates the driver version.
    * Before installing this driver, CUPS must be installed and started
      on the operating system. Also make sure that printers can be added
      and enabled by various services, according to the security level
      that has been set.
    * Because this printer driver uses the CAPT filter, Ghostscript
      needs to be installed and updated according to the system
      environment. Obtain a Ghostscript module from the website of each
      operating system's distributor in advance, according to the system
    * If Canon CAPT Printer Driver for Linux Version 1.01 or later is
      installed, you can update the existing driver without uninstalling
      it. For details about updating the printer driver, refer to
      "Updating the Printer Driver"
      <cid:part1.05090308.01020006 на gmail.com> of "2.
      Installing/Uninstalling the Printer Driver". However, you cannot
      update the Version 1.00 printer driver. Refer to "Uninstalling the
      Printer Driver" <cid:part2.02000606.02000301 на gmail.com> of "2.
      Installing/Uninstalling the Printer Driver" to uninstall the
      existing printer driver, then install the new printer driver
      according to the procedure below.
    * To check the version of the printer driver you are using, refer to
      "Checking the Driver Version"
      <cid:part3.07010003.04060003 на gmail.com> in the "Appendix".
    * You cannot print with this printer driver if LBP-1210 is being
      used in parallel connection.
    * If you want to use LBP3300 or LBP5000 on a network, you need to
      set the IP address for the network board before installing the
      printer driver. For details on setting the IP address for the
      network board, see "Specifying the IP Address for the Network
      Board" <cid:part4.04080307.05000205 на gmail.com> in "Appendix".


Start Linux after installation, and log in as 'root'.

$ su


Install the common module for CUPS driver.

Enter the following rpm command:

# rpm -ivh cndrvcups-common-1.3x-x.i386.rpm


    * When you execute the rpm command from a directory, specify the
      path or use the cd command to change the current directory to the
      directory containing the printer driver files.
    * For details about the rpm command, enter "man rpm" with the
      terminal software, such as GNOME Terminal.


Install the CAPT printer driver module.

Enter the following rpm command:

# rpm -ivh cndrvcups-capt-1.3x-x.i386.rpm


Restart CUPS.

Enter the following command:

# /etc/init.d/cups restart


    * Do not register the printer using the "lpadmin" command before
      restarting CUPS.


Register the printer (PPD) with the print spooler.

Enter the following command:

# /usr/sbin/lpadmin -p [printer name] -m [PPD file name] -v 
ccp:/var/ccpd/fifo0 -E

Example: To register the LBP5000 in the print spooler as "LBP5000":

/usr/sbin/lpadmin -p LBP5000 -m CNCUPSLBP5000CAPTK.ppd -v 
ccp:/var/ccpd/fifo0 -E


    * For the PPD file corresponding to your printer, refer to
      "Supported Canon Products" of "1. Introduction"
      <cid:part5.02070908.08020601 на gmail.com>.


Register the printer in the ccpd daemon setup file.

USB Connection

Enter the following rpm command:

# /usr/sbin/ccpdadmin -p [Printer Name] -o [Printer Device Path]

Example: To register LBP5000 in the ccpd daemon setup file:

/usr/sbin/ccpdadmin -p LBP5000 -o /dev/usb/lp0


Start ccpd daemon.

Enter the following command.

# /etc/init.d/ccpd start


    * It would be convenient to set ccpd daemon to start automatically
      when Linux starts up.

Соответственно LBP5000 я заменял на LBP2900, cups перед установкой 
запущен был, дрова ставил из под рута. Принтер не печатает. Для 
OpenOffice и Kwrite он виден, файлы на печать отправлятся, но не печатает.

Подробная информация о списке рассылки Sisyphus