[Hardware] smartctl

Andrei Lomov lomov на math.nsc.ru
Ср Янв 16 14:11:05 MSK 2008


С жестким диском, похоже, нелады ...
Пока работает, но диагностика подозрительная.
Посоветуйте, насколько это критично,
сейчас бежать в магазин, или еще потерпит?


# /usr/sbin/smartctl -a /dev/hda
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     ST3250823A
Serial Number:    5ND0RV7P
Firmware Version: 3.03
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Wed Jan 16 17:05:07 2008 NOVT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection:
Enabled.
Self-test execution status:      (   0) The previous self-test routine
completed
                                        without error or no self-test has
ever
                                        been run.
Total time to complete Offline
data collection:                 ( 430) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off
support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  84) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED 
WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   058   054   006    Pre-fail  Always      
-       24580178
  3 Spin_Up_Time            0x0003   099   098   000    Pre-fail  Always      
-       0
  4 Start_Stop_Count        0x0032   099   099   020    Old_age   Always      
-       1688
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always      
-       0
  7 Seek_Error_Rate         0x000f   077   060   030    Pre-fail  Always      
-       51790101
  9 Power_On_Hours          0x0032   095   095   000    Old_age   Always      
-       4559
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always      
-       0
 12 Power_Cycle_Count       0x0032   099   099   020    Old_age   Always      
-       1716
194 Temperature_Celsius     0x0022   039   048   000    Old_age   Always      
-       39 (Lifetime Min/Max 0/15)
195 Hardware_ECC_Recovered  0x001a   058   053   000    Old_age   Always      
-       24580178
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always      
-       1
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline     
-       1
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always      
-       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline     
-       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always      
-       0

SMART Error Log Version: 1
ATA Error Count: 83 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 83 occurred at disk power-on lifetime: 3659 hours (152 days + 11
hours)
  When the command that caused the error occurred, the device was active or
idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 52 4d 36 e0  Error: UNC at LBA = 0x00364d52 = 3558738

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 d8 08 4f 4d 36 e0 00      00:00:49.697  READ DMA EXT
  25 d8 01 d6 24 01 e0 00      00:00:49.685  READ DMA EXT
  25 d8 08 4f 4d 36 e0 00      00:00:49.685  READ DMA EXT
  25 d8 01 c8 d3 60 e0 00      00:00:49.684  READ DMA EXT
  25 d8 01 00 00 00 e0 00      00:00:49.677  READ DMA EXT

Error 82 occurred at disk power-on lifetime: 3659 hours (152 days + 11
hours)
  When the command that caused the error occurred, the device was active or
idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 52 4d 36 e0  Error: UNC at LBA = 0x00364d52 = 3558738

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 d8 08 4f 4d 36 e0 00      00:00:49.697  READ DMA EXT
  25 d8 01 c8 d3 60 e0 00      00:00:49.685  READ DMA EXT
  25 d8 01 00 00 00 e0 00      00:00:49.685  READ DMA EXT
  25 d8 01 00 00 00 e0 00      00:00:49.684  READ DMA EXT
  25 d8 20 81 1b 09 e0 00      00:00:49.677  READ DMA EXT

Error 81 occurred at disk power-on lifetime: 3659 hours (152 days + 11
hours)
  When the command that caused the error occurred, the device was active or
idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 52 4d 36 e0  Error: UNC at LBA = 0x00364d52 = 3558738

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 d8 08 4f 4d 36 e0 00      00:00:45.943  READ DMA EXT
  25 d8 08 ef 99 1c e0 00      00:00:45.941  READ DMA EXT
  25 d8 08 e7 99 1c e0 00      00:00:45.940  READ DMA EXT
  25 d8 08 47 ea 08 e0 00      00:00:45.933  READ DMA EXT
  25 d8 08 3f ea 08 e0 00      00:00:45.922  READ DMA EXT

Error 80 occurred at disk power-on lifetime: 3641 hours (151 days + 17
hours)
  When the command that caused the error occurred, the device was active or
idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 52 4d 36 e0  Error: UNC at LBA = 0x00364d52 = 3558738

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 d8 08 4f 4d 36 e0 00      01:04:18.094  READ DMA EXT
  25 d8 40 21 18 0b e0 00      01:04:18.093  READ DMA EXT
  25 d8 3d 59 1b 0b e0 00      01:04:18.092  READ DMA EXT
  35 d8 08 3f 6f 71 e0 00      01:04:18.092  WRITE DMA EXT
  25 d8 20 9a 1b 0b e0 00      01:04:18.092  READ DMA EXT

Error 79 occurred at disk power-on lifetime: 3641 hours (151 days + 17
hours)
  When the command that caused the error occurred, the device was active or
idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 52 4d 36 e0  Error: UNC at LBA = 0x00364d52 = 3558738

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 d8 08 4f 4d 36 e0 00      01:03:46.319  READ DMA EXT
  25 d8 18 df 6c 0a e0 00      01:03:46.314  READ DMA EXT
  35 d8 08 0f 53 0a e0 00      01:03:46.314  WRITE DMA EXT
  35 d8 08 1f 4f 0a e0 00      01:03:46.305  WRITE DMA EXT
  35 d8 08 97 70 71 e0 00      01:03:46.305  WRITE DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours) 
LBA_of_first_error
# 1  Short offline       Completed without error       00%         0        
-
# 2  Short offline       Completed without error       00%         0        
-

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.




-- 
Всего доброго,
А.Л.




Подробная информация о списке рассылки Hardware