[Hardware] Fwd: Re: [Comm] Поделитесь конфигом для fgrlx

Michael Shigorin mike на osdn.org.ua
Вс Ноя 14 13:41:25 MSK 2004

----- Forwarded message from Sergey Sharavin <sharavin at sibmail.ru> -----

Date: Sun, 14 Nov 2004 15:37:38 +0600
From: Sergey Sharavin <sharavin at sibmail.ru>
To: community at altlinux.ru
Subject: Re: [Comm] Поделитесь конфигом для fgrlx

some_x пишет:

>scor wrote:
>>some_x wrote:
>>>Народ,  у кого работает 3d ускорение c драйвером fgrlx на АЛМ2.4, 
>>>киньте, плиз, в меня конфигом, а то вроде беру рабочий, а он не пашет.
>>Что за видюха то? Какая система.
>radeon 9600, ALM 2.4, пытался генерировать ati`ной утилитой, в 
>результате система виснет яростно шурша винтом, так как я в последнее 
>время много глючу

У меня тоже Radeon 9600 3D работает.
Может Вам поможет мой конфиг.

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
   Identifier  "Standard VGA"
   VendorName  "Unknown"
   BoardName   "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset     "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

   Driver      "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# installed.

#    BusID       "PCI:0:10:0"

#    VideoRam    256

#    Clocks      25.2 28.3


# === ATI device section ===

Section "Device"
   Identifier                          "ATI Graphics Adapter"
   Driver                              "fglrx"
# ### generic DRI settings ###
# === disable PnP Monitor  ===
   #Option                              "NoDDC"
# === disable/enable XAA/DRI ===
   Option "no_accel"                   "no"
   Option "no_dri"                     "no"
# === misc DRI settings ===
   Option "mtrr"                       "off" # disable DRI mtrr mapper, 
driver has its own code for mtrr
# ### FireGL DDX driver module specific settings ###
# === Screen Management ===
   Option "DesktopSetup"               "0x00000000"
   Option "MonitorLayout"              "AUTO, AUTO"
   Option "IgnoreEDID"                 "off"
   Option "HSync2"                     "unspecified"
   Option "VRefresh2"                  "unspecified"
   Option "ScreenOverlap"              "0"
# === TV-out Management ===
   Option "NoTV"                       "no"    
   Option "TVStandard"                 "PAL-D"    
   Option "TVHSizeAdj"                 "0"    
   Option "TVVSizeAdj"                 "0"    
   Option "TVHPosAdj"                  "0"    
   Option "TVVPosAdj"                  "0"    
   Option "TVHStartAdj"                "0"    
   Option "TVColorAdj"                 "0"    
   Option "GammaCorrectionI"           "0x00000000"
   Option "GammaCorrectionII"          "0x00000000"
# === OpenGL specific profiles/settings ===
   Option "Capabilities"               "0x00000000"
# === Video Overlay for the Xv extension ===
   Option "VideoOverlay"               "on"
# === OpenGL Overlay ===
# Note: When OpenGL Overlay is enabled, Video Overlay
#       will be disabled automatically
   Option "OpenGLOverlay"              "off"
# === Center Mode (Laptops only) ===
   Option "CenterMode"                 "off"
# === Pseudo Color Visuals (8-bit visuals) ===
   Option "PseudoColorVisuals"         "off"
# === QBS Management ===
   Option "Stereo"                     "off"
   Option "StereoSyncEnable"           "1"
# === FSAA Management ===
   Option "FSAAEnable"                 "yes"
   Option "FSAAScale"                  "6"
   Option "FSAADisableGamma"           "no"
   Option "FSAACustomizeMSPos"         "no"
   Option "FSAAMSPosX0"                "0.000000"
   Option "FSAAMSPosY0"                "0.000000"
   Option "FSAAMSPosX1"                "0.000000"
   Option "FSAAMSPosY1"                "0.000000"
   Option "FSAAMSPosX2"                "0.000000"
   Option "FSAAMSPosY2"                "0.000000"
   Option "FSAAMSPosX3"                "0.000000"
   Option "FSAAMSPosY3"                "0.000000"
   Option "FSAAMSPosX4"                "0.000000"
   Option "FSAAMSPosY4"                "0.000000"
   Option "FSAAMSPosX5"                "0.000000"
   Option "FSAAMSPosY5"                "0.000000"
# === Misc Options ===
   Option "UseFastTLS"                 "0"
   Option "BlockSignalsOnLock"         "on"
   Option "UseInternalAGPGART"         "yes"
   Option "ForceGenericCPU"            "no"
   BusID "PCI:1:0:0"    # vendor=1002, device=4152
   Screen 0

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
   Identifier  "Screen0"
   Device      "ATI Graphics Adapter"
   Monitor     "Monitor0"
   DefaultDepth 24
   #Option "backingstore"

   Subsection "Display"
       Depth       24
       Modes       "1024x768"
       ViewPort    0 0  # initial origin if mode is smaller than desktop
#        Virtual     1280 1024

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
   Identifier  "Server Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.

   Screen "Screen0"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

   InputDevice "Mouse1" "CorePointer"
   InputDevice "Keyboard1" "CoreKeyboard"


Community mailing list
Community at altlinux.ru

----- End forwarded message -----

 ---- WBR, Michael Shigorin <mike at altlinux.ru>
  ------ Linux.Kiev http://www.linux.kiev.ua/

Подробная информация о списке рассылки Hardware