[Devel-conf] alterator: big dynamic tables

[Stanislav Ievlev]

А есть ли какие аномалии, если посмотреть в браузере на сгенерённый html?

6 мая 2008 г. 17:53 пользователь Vitaly Ostanin <vyt на altlinux.org> написал:
> Здравствуйте.
>
>  Наткнулся на очередную проблему: в динамической таблице не удаляются
>  объекты, если они находятся ниже 9 строки.
>
>  В бакенд передаются action delete только для первых 9 объектов.
>
>  У меня это воспроизводится в модуле:
>  http://git.altlinux.org/people/vyt/packages/?p=alterator-amanda.git;a=summary
>
>  На всякий случай приложен извращённый disklist, с которым это
>  происходит (нужно положить в /etc/amanda/<config name>/)
>
>  Попробовал воспроизвести в alterator-amanda (virtual hosts) - не
>  воспроизводится.
>
>  Версии пакетов alterator из сегодняшнего сизифа.
>  alterator-3.2-alt6
>  alterator-fbi-2.2-alt5
>
>  --
>  Regards, Vyt
>  mailto:  vyt на altlinux.org
>  JID:     vitaly.ostanin на gmail.com
>
> # sample Amanda2 disklist file, derived from CS.UMD.EDU's disklist
>  #
>  # If your configuration is called, say, "csd2", then this file normally goes
>  # in /etc/amanda/csd2/disklist.
>  #
>  # File format is:
>  #
>  #       hostname diskdev dumptype
>  #
>  # where the dumptypes are defined by you in amanda.conf.
>
>
>  # At our site, root partitions have a different dumptype because they
>  # are of lower priority; they don't contain user data, and don't change
>  # much from the department prototype.  In a crunch, they can be left for
>  # last or skipped.
>
>  ## A SPARCstation 1+
>  #salty sd0a comp-root
>  #salty sd0g comp-user
>  #salty sd1g comp-user
>  #salty sd2a comp-root
>  #salty sd2g comp-user
>  #salty sd3c comp-user
>  #
>  ## A DECstation 3100
>  #slithy rz1a comp-root
>  #slithy rz1g comp-user
>  #slithy rz3a comp-root
>  #slithy rz3g comp-user
>  #
>  ## We don't run compression on the master host since it is going to be
>  ## busy enough running amanda.
>  #master sd0a nocomp-root -1 local
>  #master sd0g nocomp-user -1 local
>  ## note: -1 is a placeholder for the spindle number
>  ## the holding disk can't be dumped to itself, it uses a disktype that
>  ## specifies the "no-hold" option (see amanda.conf).
>  #master sd1c holding-disk -1 local
>  #
>  ## The chairman's disk is high priority to make sure it gets done.
>  #bigwig sd0a comp-root
>  #bigwig sd0g comp-high
>  ## Likewise the named databases in the root partition on our primary
>  ## nameserver.  Also, compression is turned off because we don't want
>  ## to create any unnecessary load on this baby (it's only a Sun3).
>  #bozo        sd0a nocomp-high
>  #bozo        sd0g nocomp-user
>  #bozo        sd4c nocomp-user
>  #
>  ## Dump Joe's NetBSD machine, with the mounted MS-DOS partition dumped
>  ## using tar.
>  #joespc  wd0a comp-root
>  #joespc  wd0e comp-user
>  #joespc /msdos comp-user-tar
>  #
>  ## Some really slow machines, like Sun2's and some Vaxstations, take
>  ## forever to compress their dumps: it's just not worth it.
>  #
>  ## A Sun2
>  #cleo     sd0a nocomp-root
>  #cleo     sd0g nocomp-user
>  ## A VaxStation
>  #susie         rz8a nocomp-root
>  #susie         rz8g nocomp-user
>  #
>  ## and so on ... well, you get the idea
>
>  localhost /etc compressed-tar # comment
>  localhost "/home/vyt/temp temp" compressed-tar
>  localhost "/home/vyt/repo" compressed-tar
>  localhost "/a$" compressed-tar
>  localhost "/a-`~!@#$" compressed-tar
>  localhost "/a$%" compressed-tar
>  localhost "/a%^" compressed-tar
>  localhost "/a#%^&" compressed-tar
>  localhost "/a#$%^^&" compressed-tar
>  localhost "/a#$^&*" compressed-tar
>  localhost "/a%#&^&*^%$(" compressed-tar
>  localhost "/a@#%&&^**()" compressed-tar
>  localhost "/a#$%^^&&*()" compressed-tar
>  localhost "/a#$%^^&&*()-" compressed-tar
>  localhost "/a#$%^^&&3*()-" compressed-tar
>  localhost "/a#$%^^&&*()-+" compressed-tar
>  localhost "/a#$%^^&&*()-+3" compressed-tar
>
> _______________________________________________
>  devel-conf mailing list
>  devel-conf на lists.altlinux.org
>  https://lists.altlinux.org/mailman/listinfo/devel-conf
>