[Comm] Linux. Настройка COM-портов. [JT]
Алексей Сиваков
Aleksey.Sivakov на ya.ru
Вт Май 14 17:13:24 MSK 2013
Michael A. Kangin пишет:
> Походу на эту плату нужен специально обученный модуль ядра.
> Посмотрите lspci -k, как она видна, и загружен ли какой-нибудь модуль.
>
> Если модуль есть, смотрите лог загрузки dmesg - порты с неё могут быть
> названы как-то экзотически.
Вложил выводы команд.
Где встроенный COM-порт я понять не могу, но внешняя плата с COMами -
NetMos Technology PCI 9835 Multi-I/O Controller (rev 01). В GUI-утилите
тоже показывает в графе неизвестных устройств (как и какую-то
макинтош-мышь). Какой модуль надо и где его взять?
----------- следующая часть -----------
Linux version 2.6.27-desktop-0.rc8.2mnb (pterjan на klodia.mandriva.com) (gcc version 4.3.2 (GCC) ) #1 SMP Thu Oct 2 05:49:37 EDT 2008
Command line: BOOT_IMAGE=linux root=UUID=36b13f94-b34d-11e2-88bd-c3581079cb6c resume=UUID=397bb72c-b34d-11e2-81f3-81a02c7f6009 splash=silent vga=788
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e7000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000037fb0000 (usable)
BIOS-e820: 0000000037fb0000 - 0000000037fc0000 (ACPI data)
BIOS-e820: 0000000037fc0000 - 0000000037ff0000 (ACPI NVS)
BIOS-e820: 0000000037ff0000 - 0000000038000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
last_pfn = 0x37fb0 max_arch_pfn = 0x3ffffffff
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
init_memory_mapping
0000000000 - 0037e00000 page 2M
0037e00000 - 0037fb0000 page 4k
kernel direct mapping tables up to 37fb0000 @ 8000-b000
last_map_addr: 37fb0000 end: 37fb0000
RAMDISK: 37bed000 - 37f9f3d7
DMI present.
ACPI: RSDP 000FA4F0, 0014 (r0 ACPIAM)
ACPI: RSDT 37FB0000, 0044 (r1 A_M_I OEMRSDT 3001109 MSFT 97)
ACPI: FACP 37FB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT 97)
ACPI: DSDT 37FB0460, 494B (r1 AS359 AS359142 142 INTL 20051117)
ACPI: FACS 37FC0000, 0040
ACPI: APIC 37FB0390, 0090 (r1 A_M_I OEMAPIC 3001109 MSFT 97)
ACPI: MCFG 37FB0420, 003C (r1 A_M_I OEMMCFG 3001109 MSFT 97)
ACPI: OEMB 37FC0040, 0061 (r1 A_M_I AMI_OEM 3001109 MSFT 97)
ACPI: SRAT 37FB4DB0, 0090 (r3 AMD FAM_F_10 2 AMD 1)
ACPI: MSCT 37FB4E40, 004E (r1 A M I OEMBOARD 1 AMD 1)
ACPI: AAFT 37FB4E90, 0027 (r1 A_M_I OEMAAFT 3001109 MSFT 97)
ACPI: SSDT 37FB4EC0, 023E (r1 A M I POWERNOW 1 AMD 1)
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: Node 0 PXM 0 0-a0000
SRAT: Node 0 PXM 0 100000-40000000
NUMA: Allocated memnodemap from 9000 - 9880
NUMA: Using 20 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000037fb0000
NODE_DATA [0000000000001000 - 0000000000005fff]
bootmap [000000000000a000 - 0000000000010ff7] pages 7
(7 early reservations) ==> bootmem [0000000000 - 0037fb0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 00007f194c] TEXT DATA BSS ==> [0000200000 - 00007f194c]
#3 [0037bed000 - 0037f9f3d7] RAMDISK ==> [0037bed000 - 0037f9f3d7]
#4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#5 [0000008000 - 0000009000] PGTABLE ==> [0000008000 - 0000009000]
#6 [0000009000 - 0000009880] MEMNODEMAP ==> [0000009000 - 0000009880]
found SMP MP-table at [ffff8800000ff780] 000ff780
[ffffe20000000000-ffffe20000dfffff] PMD -> [ffff880001200000-ffff880001ffffff] on node 0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x00037fb0
On node 0 totalpages: 229199
DMA zone: 2320 pages, LIFO batch:0
DMA32 zone: 222121 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x508
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 6 CPUs, 5 hotplug CPUs
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e7000
PM: Registered nosave memory: 00000000000e7000 - 0000000000100000
Allocating PCI resources starting at 40000000 (gap: 38000000:c6c00000)
PERCPU: Allocating 51744 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 6, nr_node_ids 1
Built 1 zonelists in Node order, mobility grouping on. Total pages: 224441
Policy zone: DMA32
Kernel command line: BOOT_IMAGE=linux root=UUID=36b13f94-b34d-11e2-88bd-c3581079cb6c resume=UUID=397bb72c-b34d-11e2-81f3-81a02c7f6009 splash=silent vga=788
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PMTIMER calibration value
Detected 2812.784 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour dummy device 80x25
console [tty0] enabled
Checking aperture...
No AGP bridge found
Node 0: aperture @ 8300000000 size 32 MB
Aperture beyond 4GB. Ignoring.
Memory: 892124k/917184k available (3077k kernel code, 24672k reserved, 1558k data, 540k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 5625.56 BogoMIPS (lpj=2812780)
Security Framework initialized
AppArmor: AppArmor disabled by boottime parameter
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
Hook version: 2.6.27-2.3 2008/08/29
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
tseg: 0000000000
using C1E aware idle routine
Early unpacking initramfs... done
Freeing initrd memory: 3784k freed
ACPI: Core revision 20080609
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
CPU0: AMD Sempron(tm) 145 Processor stepping 03
Using local APIC timer interrupts.
APIC timer calibration result 12557051
Detected 12.557 MHz APIC timer.
Brought up 1 CPUs
Total of 1 processors activated (5625.56 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0 level NODE
groups: 0
net_namespace: 1552 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
node 0 link 0: io port [1000, ffffff]
TOM: 0000000040000000 aka 1024M
Fam 10h mmconf [fc000000, fdffffff]
node 0 link 0: mmio [fc000000, fdffffff] ==> none
node 0 link 0: mmio [40000000, fbffffff]
node 0 link 0: mmio [fe000000, fe0bffff]
node 0 link 0: mmio [a0000, bffff]
bus: [00,07] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [40000000, fbffffff]
bus: 00 index 2 mmio: [fe000000, fcffffffff]
bus: 00 index 3 mmio: [a0000, bffff]
ACPI: bus type pci registered
PCI: MCFG configuration 0: base fc000000 segment 0 buses 0 - 31
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
PCI: Using configuration type 1 for extended access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base fc000000 segment 0 buses 0 - 31
PCI: MCFG area at fc000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at fc000000 - fdffffff
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: 0000:00:01.0 reg 10 io port: [900, 9ff]
PCI: 0000:00:01.1 reg 10 io port: [dc00, dc3f]
PCI: 0000:00:01.1 reg 20 io port: [600, 63f]
PCI: 0000:00:01.1 reg 24 io port: [700, 73f]
pci 0000:00:01.1: PME# supported from D3hot D3cold
pci 0000:00:01.1: PME# disabled
PCI: 0000:00:02.0 reg 10 32bit mmio: [fbfff000, fbffffff]
pci 0000:00:02.0: supports D1
pci 0000:00:02.0: supports D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
PCI: 0000:00:02.1 reg 10 32bit mmio: [fbffec00, fbffecff]
pci 0000:00:02.1: supports D1
pci 0000:00:02.1: supports D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.1: PME# disabled
PCI: 0000:00:05.0 reg 10 32bit mmio: [fbff8000, fbffbfff]
pci 0000:00:05.0: PME# supported from D3hot D3cold
pci 0000:00:05.0: PME# disabled
PCI: 0000:00:06.0 reg 20 io port: [ffa0, ffaf]
PCI: 0000:00:07.0 reg 10 32bit mmio: [fbffd000, fbffdfff]
PCI: 0000:00:07.0 reg 14 io port: [d480, d487]
pci 0000:00:07.0: supports D1
pci 0000:00:07.0: supports D2
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
PCI: 0000:00:08.0 reg 10 io port: [d400, d407]
PCI: 0000:00:08.0 reg 14 io port: [d080, d083]
PCI: 0000:00:08.0 reg 18 io port: [d000, d007]
PCI: 0000:00:08.0 reg 1c io port: [cc00, cc03]
PCI: 0000:00:08.0 reg 20 io port: [c880, c88f]
PCI: 0000:00:08.0 reg 24 32bit mmio: [fbffc000, fbffcfff]
PCI: 0000:00:08.1 reg 10 io port: [c800, c807]
PCI: 0000:00:08.1 reg 14 io port: [c480, c483]
PCI: 0000:00:08.1 reg 18 io port: [c400, c407]
PCI: 0000:00:08.1 reg 1c io port: [c080, c083]
PCI: 0000:00:08.1 reg 20 io port: [c000, c00f]
PCI: 0000:00:08.1 reg 24 32bit mmio: [fbff7000, fbff7fff]
pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:09.0: PME# disabled
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0c.0: PME# disabled
PCI: 0000:00:0d.0 reg 10 32bit mmio: [fa000000, faffffff]
PCI: 0000:00:0d.0 reg 14 32bit mmio: [e0000000, efffffff]
PCI: 0000:00:0d.0 reg 1c 64bit mmio: [f9000000, f9ffffff]
PCI: 0000:00:0d.0 reg 30 32bit mmio: [fbfc0000, fbfdffff]
PCI: 0000:01:0a.0 reg 10 io port: [ec00, ec07]
PCI: 0000:01:0a.0 reg 14 io port: [e880, e887]
PCI: 0000:01:0a.0 reg 18 io port: [e800, e807]
PCI: 0000:01:0a.0 reg 1c io port: [e480, e487]
PCI: 0000:01:0a.0 reg 20 io port: [e400, e407]
PCI: 0000:01:0a.0 reg 24 io port: [e080, e08f]
pci 0000:00:04.0: transparent bridge
PCI: bridge 0000:00:04.0 io port: [e000, efff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 12, should be 11 [20080609]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
DMAR:parse DMAR table failure.
ACPI: RTC can wake from S4
system 00:05: ioport range 0x4d0-0x4d1 has been reserved
system 00:05: ioport range 0x500-0x57f has been reserved
system 00:05: ioport range 0x580-0x5ff has been reserved
system 00:05: ioport range 0x800-0x87f has been reserved
system 00:05: ioport range 0x880-0x8ff has been reserved
system 00:05: ioport range 0xd00-0xd7f has been reserved
system 00:05: ioport range 0xd80-0xdff has been reserved
system 00:05: ioport range 0x1100-0x117f has been reserved
system 00:05: ioport range 0x1180-0x11ff has been reserved
system 00:05: iomem range 0xfec80000-0x1fd93ffff could not be reserved
system 00:05: iomem range 0xfefe0000-0xfefe01ff has been reserved
system 00:05: iomem range 0xfefe1000-0xfefe1fff has been reserved
system 00:05: iomem range 0xfee01000-0xfeefffff could not be reserved
system 00:06: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:06: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:09: ioport range 0x280-0x28f has been reserved
system 00:09: ioport range 0x290-0x29f has been reserved
system 00:0a: iomem range 0xfc000000-0xfdffffff has been reserved
system 00:0b: iomem range 0x0-0x9ffff could not be reserved
system 00:0b: iomem range 0xc0000-0xcffff has been reserved
system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
system 00:0b: iomem range 0x100000-0x3fffffff could not be reserved
system 00:0b: iomem range 0xff380000-0xffffffff could not be reserved
pci 0000:00:04.0: PCI bridge, secondary bus 0000:01
pci 0000:00:04.0: IO window: 0xe000-0xefff
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:09.0: PCI bridge, secondary bus 0000:02
pci 0000:00:09.0: IO window: disabled
pci 0000:00:09.0: MEM window: disabled
pci 0000:00:09.0: PREFETCH window: disabled
pci 0000:00:0b.0: PCI bridge, secondary bus 0000:03
pci 0000:00:0b.0: IO window: disabled
pci 0000:00:0b.0: MEM window: disabled
pci 0000:00:0b.0: PREFETCH window: disabled
pci 0000:00:0c.0: PCI bridge, secondary bus 0000:04
pci 0000:00:0c.0: IO window: disabled
pci 0000:00:0c.0: MEM window: disabled
pci 0000:00:0c.0: PREFETCH window: disabled
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:09.0: setting latency timer to 64
pci 0000:00:0b.0: setting latency timer to 64
pci 0000:00:0c.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 io port: [e000, efff]
bus: 01 index 1 mmio: [0, 0]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 io port: [0, ffff]
bus: 01 index 4 mmio: [0, ffffffffffffffff]
bus: 02 index 0 mmio: [0, 0]
bus: 02 index 1 mmio: [0, 0]
bus: 02 index 2 mmio: [0, 0]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 mmio: [0, 0]
bus: 03 index 1 mmio: [0, 0]
bus: 03 index 2 mmio: [0, 0]
bus: 03 index 3 mmio: [0, 0]
bus: 04 index 0 mmio: [0, 0]
bus: 04 index 1 mmio: [0, 0]
bus: 04 index 2 mmio: [0, 0]
bus: 04 index 3 mmio: [0, 0]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(1368550534.162:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 1749
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:00.0: Enabling HT MSI Mapping
pci 0000:00:04.0: Enabling HT MSI Mapping
pci 0000:00:05.0: Enabling HT MSI Mapping
pci 0000:00:07.0: Enabling HT MSI Mapping
pci 0000:00:08.0: Enabling HT MSI Mapping
pci 0000:00:08.1: Enabling HT MSI Mapping
pci 0000:00:09.0: Enabling HT MSI Mapping
pci 0000:00:0b.0: Enabling HT MSI Mapping
pci 0000:00:0c.0: Enabling HT MSI Mapping
pci 0000:00:0d.0: Boot video device
pcieport-driver 0000:00:09.0: setting latency timer to 64
pcieport-driver 0000:00:09.0: found MSI capability
pci_express 0000:00:09.0:pcie00: allocate port service
pci_express 0000:00:09.0:pcie03: allocate port service
pcieport-driver 0000:00:0b.0: setting latency timer to 64
pcieport-driver 0000:00:0b.0: found MSI capability
pci_express 0000:00:0b.0:pcie00: allocate port service
pci_express 0000:00:0b.0:pcie03: allocate port service
pcieport-driver 0000:00:0c.0: setting latency timer to 64
pcieport-driver 0000:00:0c.0: found MSI capability
pci_express 0000:00:0c.0:pcie00: allocate port service
pci_express 0000:00:0c.0:pcie03: allocate port service
vesafb: framebuffer at 0xe0000000, mapped to 0xffffc20002580000, using 1875k, total 131072k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
Linux agpgart interface v0.103
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
registered taskstats version 1
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 540k freed
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 23
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ehci_hcd 0000:00:02.1: irq 23, io mem 0xfbffec00
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
Switched to high resolution mode on CPU 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-desktop-0.rc8.2mnb ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 22
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 22, io mem 0xfbfff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-desktop-0.rc8.2mnb ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
No dock devices found.
libata version 3.00 loaded.
sata_nv 0000:00:08.0: version 3.5
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
sata_nv 0000:00:08.0: PCI INT A -> Link[LSA0] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:08.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xc880 irq 21
ata2: SATA max UDMA/133 cmd 0xd000 ctl 0xcc00 bmdma 0xc888 irq 21
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: New USB device found, idVendor=0c2e, idProduct=0200
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: Honeywell Scanning and Mobility Scanner
usb 2-1: Manufacturer: Honeywell Scanning and Mobility
usb 2-3: new low speed USB device using ohci_hcd and address 3
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: New USB device found, idVendor=15d9, idProduct=0a4c
usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3: Product: USB OPTICAL MOUSE
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-8: ST3160316AS, JC4B, max UDMA/133
ata2.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
isa bounce pool size: 16 pages
scsi 1:0:0:0: Direct-Access ATA ST3160316AS JC4B PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 1:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 20
sata_nv 0000:00:08.1: PCI INT B -> Link[LSA1] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:08.1: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc000 irq 20
ata4: SATA max UDMA/133 cmd 0xc400 ctl 0xc080 bmdma 0xc008 irq 20
pata_amd 0000:00:06.0: version 0.3.10
pata_amd 0000:00:06.0: setting latency timer to 64
scsi4 : pata_amd
scsi5 : pata_amd
ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata6: port disabled. ignoring.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
TomoyoLinux Mandatory Access Control disabled by default.
You need to install ccs-tools if you want to enable it.
sd 1:0:0:0: Attached scsi generic sg0 type 0
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 23
forcedeth 0000:00:07.0: PCI INT A -> Link[LMAC] -> GSI 23 (level, low) -> IRQ 23
forcedeth 0000:00:07.0: setting latency timer to 64
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:25:22:db:c6:b4
forcedeth 0000:00:07.0: highdma pwrctl mgmt timirq lnktim msi desc-v3
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
parport_serial 0000:01:0a.0: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ 19
parport0: PC-style at 0xe800 [PCSPP,TRISTATE,EPP]
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x600
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x700
processor ACPI0007:00: registered as cooling_device0
input: Power Button (FF) as /class/input/input2
usbcore: registered new interface driver hiddev
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
input: Honeywell Scanning and Mobility Honeywell Scanning and Mobility Scanner as /class/input/input4
ACPI: Power Button (CM) [PWRB]
0000:01:0a.0: ttyS1 at I/O 0xec00 (irq = 19) is a 16550A
0000:01:0a.0: ttyS2 at I/O 0xe880 (irq = 19) is a 16550A
input,hidraw0: USB HID v1.11 Keyboard [Honeywell Scanning and Mobility Honeywell Scanning and Mobility Scanner] on usb-0000:00:02.0-1
input: USB OPTICAL MOUSE as /class/input/input5
input,hidraw1: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:02.0-3
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
ppdev: user-space parallel port driver
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
HDA Intel 0000:00:05.0: PCI INT B -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:05.0: setting latency timer to 64
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel на redhat.com
EXT3 FS on sda5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
loop: module loaded
Adding 4089920k swap on /dev/sda6. Priority:-1 extents:1 across:4089920k
hda_codec: num_steps = 0 for NID=0x1a (ctl = Mic Boost)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no link during initialization.
ADDRCONF(NETDEV_UP): eth0: link is not ready
----------- следующая часть -----------
Module Size Used by
nls_iso8859_1 9344 1
nls_cp437 11008 1
vfat 16384 1
fat 58168 1 vfat
ipv6 299368 26
binfmt_misc 14220 1
loop 21388 0
fuse 62528 1
dm_mod 63984 0
ppdev 12680 0
snd_hda_intel 527696 0
snd_hwdep 12552 1 snd_hda_intel
snd_seq_dummy 7300 0
snd_seq_oss 37760 0
snd_seq_midi_event 11520 1 snd_seq_oss
snd_seq 60320 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 11284 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 47520 0
snd_pcm 86920 2 snd_hda_intel,snd_pcm_oss
parport_serial 11392 0
usbhid 56672 0
snd_timer 27536 2 snd_seq,snd_pcm
ff_memless 9864 1 usbhid
snd_page_alloc 13328 2 snd_hda_intel,snd_pcm
parport_pc 39336 1 parport_serial
parport 41648 2 ppdev,parport_pc
snd_mixer_oss 20608 1 snd_pcm_oss
thermal 22944 0
button 11552 0
snd 66376 9 snd_hda_intel,snd_hwdep,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
processor 43448 1 thermal
soundcore 11424 1 snd
i2c_nforce2 11272 0
i2c_core 27552 1 i2c_nforce2
rtc_cmos 15160 0
evdev 15904 4
sg 40288 0
forcedeth 63632 0
usb_storage 118596 1
pata_amd 17924 0
sata_nv 30856 3
libata 175200 2 pata_amd,sata_nv
dock 13472 1 libata
sd_mod 41128 6
scsi_mod 163704 4 sg,usb_storage,libata,sd_mod
crc_t10dif 6016 1 sd_mod
ext3 143760 2
jbd 56744 1 ext3
uhci_hcd 29728 0
ohci_hcd 30364 0
ehci_hcd 43148 0
usbcore 161424 6 usbhid,usb_storage,uhci_hcd,ohci_hcd,ehci_hcd
----------- следующая часть -----------
00:00.0 RAM memory: nVidia Corporation MCP61 LPC Bridge (rev a1)
00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2)
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3)
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3)
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1)
00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2)
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2)
Kernel driver in use: pata_amd
Kernel modules: amd74xx, ide-pci-generic, ata_generic, pata_amd, pata_acpi
00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2)
Kernel driver in use: forcedeth
Kernel modules: forcedeth, isp1760
00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2)
Kernel driver in use: sata_nv
Kernel modules: ide-pci-generic, ata_generic, pata_acpi, sata_nv
00:08.1 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2)
Kernel driver in use: sata_nv
Kernel modules: ide-pci-generic, ata_generic, pata_acpi, sata_nv
00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0d.0 VGA compatible controller: nVidia Corporation Device 03d6 (rev a2)
Kernel modules: nvidiafb
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Link Control
01:0a.0 Communication controller: NetMos Technology PCI 9835 Multi-I/O Controller (rev 01)
Kernel driver in use: parport_serial
Kernel modules: parport_serial
Подробная информация о списке рассылки community