[Comm] PCMCI_NIC_Xircom
andriy
=?iso-8859-1?q?l=2Eandriy_=CE=C1_gmail=2Ecom?=
Сб Мар 8 02:35:54 MSK 2008
Michael Shigorin wrote:
> On Tue, Feb 12, 2008 at 10:00:15PM +0200, andriy wrote:
>
>>> Тут я не вижу никаких упоминаний про Вашу сетевую. Она в этот момент вставленна?
>>>
>>>> 2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 1000
>>>> link/ether 00:10:a4:a1:e2:45 brd ff:ff:ff:ff:ff:ff
>>>>
>>> Тут видно, что адрес интерфейсу не присвоен. Что и не
>>> удивительно. Ведь он не поднят.
>>>
>
> В смысле ip link set up?
>
>
>> Может кто имеет токой же девайс?Посоветуйте что с ним делать?
>>
>
> Xircom, с которым сталкивался -- вполне прилично работал
> (xirc2ps_cs, кажется).
>
>
>> Карточка ведь пингуется, только правда в момент проигрывания
>> звука-приветствия, когда пользователь входит в KDE.
>>
>
> Как пингуется, на ней же адреса нет?!
>
>
Попал наконец-то этот ноут Dell Latitude CPx (Pentium III) в руки
(сетевая карта xircom,pcmcia-ная). ALT Desktop 4.0
Значит такая вот ситуация -
ip-ка есть, при старте интерфейс eth0 поднимается:
ifconfig
eth0 Link encap:Ethernet HWaddr 00:10:A4:A1:E2:45
inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:852 errors:0 dropped:0 overruns:0 frame:0
TX packets:831 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:82811 (80.8 KiB) TX bytes:76688 (74.8 KiB)
Interrupt:5 Base address:0x300
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
но сеть работает только в момент проигрывания звука (или с помощью
mpg123 или amarok'ом значения не имеет).
Такая вот ситация.
lsmod:
Module Size Used by
binfmt_misc 15368 1
kqemu 125092 0
cpufreq_powersave 6016 0
cpufreq_conservative 11912 0
cpufreq_ondemand 11020 0
cpufreq_userspace 9088 0
ac 9476 0
thermal 18568 0
processor 34792 1 thermal
button 10896 0
battery 14468 0
speedstep_lib 8708 0
freq_table 8960 0
nls_utf8 6272 1
nls_cp866 9472 1
vfat 16640 1
fat 54812 1 vfat
nls_base 11520 4 nls_utf8,nls_cp866,vfat,fat
xfs 540888 1
dm_mod 60312 0
snd_pcm_oss 47008 0
xirc2ps_cs 22796 1
serial_cs 22404 1
tsdev 11840 0
snd_maestro3 28836 4
snd_ac97_codec 103716 1 snd_maestro3
ac97_bus 6400 1 snd_ac97_codec
snd_seq_dummy 8196 0
snd_seq_oss 38656 0
irda 132792 0
snd_seq_midi_event 11520 1 snd_seq_oss
pcmcia 40892 2 xirc2ps_cs,serial_cs
parport_pc 42340 0
crc_ccitt 6272 1 irda
firmware_class 14208 1 pcmcia
snd_seq 56784 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
parport 39752 1 parport_pc
snd_seq_device 12556 3 snd_seq_dummy,snd_seq_oss,snd_seq
floppy 60516 0
snd_mixer_oss 21120 1 snd_pcm_oss
km_drv 45912 0
km_api_drv 21028 1 km_drv
videodev 26880 1 km_drv
v4l1_compat 16388 1 videodev
v4l2_common 26240 1 videodev
psmouse 41992 0
snd_pcm 81540 4 snd_pcm_oss,snd_maestro3,snd_ac97_codec
serio_raw 11140 0
snd_timer 26116 3 snd_seq,snd_pcm
snd 59112 16
snd_pcm_oss,snd_maestro3,snd_ac97_codec,snd_seq_dummy,snd_seq_oss,snd_seq,snd_seq
_device,snd_mixer_oss,snd_pcm,snd_timer
soundcore 13792 1 snd
snd_page_alloc 14088 1 snd_pcm
i2c_piix4 12428 0
i2c_core 25216 1 i2c_piix4
piix 13956 0 [permanent]
intel_agp 28692 1ide_disk 20352 5
ide_generic 5504 0 [permanent]
generic 8964 0 [permanent]
amd74xx 18076 0 [permanent]
ide_core 127560 6
piix,usb_storage,ide_disk,ide_generic,generic,amd74xx
pcspkr 7296 0
agpgart 37960 1 intel_agp
yenta_socket 30476 5
rsrc_nonstatic 17664 1 yenta_socket
pcmcia_core 43540 5
xirc2ps_cs,serial_cs,pcmcia,yenta_socket,rsrc_nonstatic
evdev 13568 1
ohci_hcd 23428 0
uhci_hcd 26764 0
usbhid 51040 0
ehci_hcd 34824 0
usb_storage 73024 0
libusual 21136 1 usb_storage
usbcore 129028 7
ohci_hcd,uhci_hcd,usbhid,ehci_hcd,usb_storage,libusual
reiserfs 238336 1
sata_nv 15108 0
libata 104468 1 sata_nv
sd_mod 24576 0
scsi_mod 137096 3 usb_storage,libata,sd_mod
dmesg:
Linux version 2.6.18-std-smp-alt10 (builder на apiary.armor.altlinux.org)
(gcc version 4.1.1 20070105 (ALT Linux, bui
ld 4.1.1-alt12)) #1 SMP Wed Dec 12 23:42:05 MSK 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000c0000 - 00000000000cc000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017fec000 (usable)
BIOS-e820: 0000000017fec000 - 0000000017ff0000 (reserved)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
383MB LOWMEM available.
On node 0 totalpages: 98284
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 94188 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000f3900
ACPI: RSDT (v001 DELL CPi R 0x27d00802 ASL 0x00000061) @ 0x17ff0000
ACPI: FADT (v001 DELL CPi R 0x27d00802 ASL 0x00000061) @ 0x17ff0400
ACPI: BOOT (v001 DELL CPi R 0x27d00802 ASL 0x00000061) @ 0x17ff07c0
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 20000000 (gap: 17ff0000:e7e10000)
Detected 647.255 MHz processor.
Built 1 zonelists. Total pages: 98284
Kernel command line: auto BOOT_IMAGE=failsafe ro
root=UUID=ce0ef6d9-36cb-4814-848b-dba677e4b602 resume=/dev/hda1 p
anic=30 splash=silent failsafe
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0130a000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 385304k/393136k available (1590k kernel code, 7396k reserved,
639k data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1295.46 BogoMIPS
(lpj=2590935)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
checking if image is initramfs... it is
Freeing initrd memory: 688k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist.
ACPI: setting ELCR to 0200 (from 0820)
CPU0: Intel Pentium III (Coppermine) stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfc0be, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 0800-083f claimed by PIIX4 ACPI
PCI quirk: region 0840-084f claimed by PIIX4 SMB
PIIX4 devres B PIO at 00e0-00e7
PIIX4 devres C PIO at 0850-085f
PIIX4 devres G PIO at 0280-0287
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: Power Resource [PADA] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 16 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:02: ioport range 0x800-0x805 could not be reserved
pnp: 00:02: ioport range 0x808-0x80f could not be reserved
pnp: 00:03: ioport range 0x806-0x807 has been reserved
pnp: 00:03: ioport range 0x850-0x853 has been reserved
pnp: 00:03: ioport range 0x856-0x85f has been reserved
pnp: 00:03: ioport range 0x810-0x83f has been reserved
pnp: 00:03: ioport range 0x840-0x84f has been reserved
pnp: 00:03: ioport range 0xa00-0xa7f has been reserved
pnp: 00:03: ioport range 0xa80-0xaff has been reserved
pnp: 00:04: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:09: ioport range 0x3f0-0x3f1 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: e000-efff
MEM window: fc000000-feffffff
PREFETCH window: 28000000-280fffff
PCI: Bus 2, cardbus bridge: 0000:00:03.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:03.1
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
PCI: Enabling device 0000:00:03.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
PCI: Enabling device 0000:00:03.1 (0000 -> 0003)
ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag at 0x79 set to 0x1
audit: initializing netlink socket (disabled)
audit(1204900521.012:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 192k freed
Executing init=/init
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: IBM-DJSA-232, ATA DISK drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 62506080 sectors (32003 MB) w/1874KiB Cache, CHS=65535/15/63
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7 >
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver libusual
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000dce0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Attempting manual resume
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first
block 18, max trans len 1024, max batch 900,
max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
Yenta: CardBus bridge found at 0000:00:03.0 [1028:00bb]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:03.0, mfunc 0x01261222, devctl 0x66
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000010
Yenta: CardBus bridge found at 0000:00:03.1 [1028:00bb]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:03.1, mfunc 0x01261222, devctl 0x66
Linux agpgart interface v0.102 (c) Dave Jones
input: PC Speaker as /class/input/input1
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000006
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xf4000000
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
PIIX4: port 0x01f0 already claimed by ide0
ide1: BM-DMA at 0x0868-0x086f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide1...
pccard: PCMCIA card inserted into slot 0
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
Linux video capture interface: v2.00
Kmultimedia API module version alpha-6.0 loaded
Kmultimedia module version alpha-6.0 loaded
Page size is 4096 sizeof(bm_list_descriptor)=16 sizeof(KM_STRUCT)=748
km: probing 0000:01:00.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
km: using irq 11
Register aperture is 0xfcfff000 0x00001000
kms variables: reg_aperture=0xd8a14000
sizeof(kmfl_template)=780 sizeof(KM_FIELD)=52
Device 0000:01:00.0 (0x1002:0x4c4d) corresponds to /dev/video0
kms variables: reg_aperture=d8a14000
Floppy drive(s): fd0 is 1.44M
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
NET: Registered protocol family 23
found SMC SuperIO Chip (devid=0x09 rev=08 base=0x03f0): FDC37N958FR
smsc_ircc_present: can't get sir_base of 0x2f8
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKB] -> GSI 5 (level, low)
-> IRQ 5
cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x200-0x207
0x280-0x287 0x370-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia0.0
cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x200-0x207
0x280-0x287 0x370-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ts: Compaq touchscreen protocol output
eth%d: MII link partner: 45e1
eth%d: MII selected
eth%d: media 100BaseT, silicon revision 5
eth0: Xircom: port 0x300, irq 5, hwaddr 00:10:A4:A1:E2:45
pcmcia: registering new device pcmcia0.1
0.1: ttyS3 at I/O 0x2e8 (irq = 5) is a 16550A
Adding 666656k swap on /dev/hda6. Priority:-1 extents:1 across:666656k
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel на redhat.com
SGI XFS with ACLs, security attributes, realtime, large block numbers,
no debug enabled
SGI XFS Quota Management subsystem
Filesystem "hda7": Disabling barriers, not supported by the underlying
device
XFS mounting filesystem hda7
Ending clean XFS mount for filesystem: hda7
FAT: utf8 is not a recommended IO charset for FAT filesystems,
filesystem will be case sensitive!
eth0: MII link partner: 05e1
eth0: MII selected
eth0: media 100BaseT, silicon revision 5
cpufreq: change failed with new_state 2 and result 0
cpufreq: change failed with new_state 2 and result 0
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THM] (32 C)
ACPI: AC Adapter [AC] (on-line)
found SMC SuperIO Chip (devid=0x09 rev=08 base=0x03f0): FDC37N958FR
smsc_ircc_present: can't get sir_base of 0x2f8
Time: acpi_pm clocksource has been installed.
mtrr: no more MTRRs available
QEMU Accelerator Module version 1.3.0, Copyright (c) 2005-2007 Fabrice
Bellard
KQEMU installed, max_locked_mem=193124kB.
mtrr: no more MTRRs available
lspci
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 03)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev 03)
00:03.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
00:03.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
00:08.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i
PCI Audio Accelerator (rev 10)
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility
P/M AGP 2x (rev 64)
lspcmcia
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:00:03.0)
Socket 0 Device 0: [xirc2ps_cs] (bus ID: 0.0)
Socket 0 Device 1: [serial_cs] (bus ID: 0.1)
Socket 1 Bridge: [yenta_cardbus] (bus ID: 0000:00:03.1)
Как заставить просто работать сетевую, без проигрывания музыки?
Спасибо за советы.
ps. 1) Под Offtopic 2000 работает.
2) Ставлю такой вот експеримент -
делаю cat /dev/dsp - сеть работает(пинги и все прочее ходит).
Ето какая-то увязка со звуковой картой но какая...
Подробная информация о списке рассылки community