[Comm] eth0, eth1, eth2

[Andrei Lomov]

Подскажите, пожалуйста, как проблему побороть.

Есть машина, включенная в сеть по eth1,
на ней еще две карты eth0, eth2, по которым подключены 
две машины из локалки:

[andrei на main andrei]$ /sbin/ifconfig
eth0      Link encap:Ethernet  HWaddr 00:05:5D:81:2D:65  
          inet addr:10.1.1.1  Bcast:10.1.1.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:202599 errors:0 dropped:0 overruns:0 frame:0
          TX packets:251181 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:23403936 (22.3 Mb)  TX bytes:135303304 (129.0 Mb)
          Interrupt:10 Base address:0xc000 

eth1      Link encap:Ethernet  HWaddr 00:05:5D:81:2D:66  
          inet addr:172.22.60.13  Bcast:172.22.60.127  Mask:255.255.255.128
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3128 errors:0 dropped:0 overruns:0 frame:0
          TX packets:19101 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:3021687 (2.8 Mb)  TX bytes:939141 (917.1 Kb)
          Interrupt:11 Base address:0xc400 

eth2      Link encap:Ethernet  HWaddr 00:11:95:F5:2B:69  
          inet addr:10.1.1.1  Bcast:10.1.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:845 errors:0 dropped:0 overruns:0 frame:0
          TX packets:15 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:83557 (81.5 Kb)  TX bytes:630 (630.0 b)
          Interrupt:5 Base address:0xc800 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:1104 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1104 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:123651 (120.7 Kb)  TX bytes:123651 (120.7 Kb)



Подключаю машину кабелем к eth0, все работает.

Тот же кабель перебрасываю на eth2 -- нет пинга.

Лампочка на eth2 моргает.

Что-то не пойму, в чем может быть проблема...

В messages вроде все нормально ?:
...
eth0: VIA VT6105 Rhine-III at 0xc000, 00:05:5d:81:2d:65, IRQ 10.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
eth1: VIA VT6105 Rhine-III at 0xc400, 00:05:5d:81:2d:66, IRQ 11.
eth1: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
eth2: VIA VT6105 Rhine-III at 0xc800, 00:11:95:f5:2b:69, IRQ 5.
eth2: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
eth1: Setting full-duplex based on MII #1 link partner capability of 41e1.
...
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
eth0: Setting half-duplex based on MII #1 link partner capability of 0000.
eth2: Setting full-duplex based on MII #1 link partner capability of 45e1.
eth2: Setting half-duplex based on MII #1 link partner capability of 0000.
eth2: Setting full-duplex based on MII #1 link partner capability of 45e1.
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
eth2: Setting half-duplex based on MII #1 link partner capability of 0000.
...

-- 
Всего доброго,
А.Л.