[Comm] cdrecord _NEC

[sinom]

Здравствуйте!

Сегодня приобрел резак фирмы NEC.
В lilo.conf прописал append="hdb=ide-scsi" после чего появилось:

$ cdrecord -scanbus
Cdrecord 2.0 (i586-alt-linux-gnu) Copyright (C) 1995-2002 JЖrg Schilling
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
scsibus0:
        0,0,0     0) '_NEC    ' 'CD-RW NR-9300A  ' '2.12' Removable CD-ROM
        0,1,0     1) *
        0,2,0     2) *
        0,3,0     3) *
        0,4,0     4) *
        0,5,0     5) *
        0,6,0     6) *
        0,7,0     7) *

При попытке что-либо писать пишет только первые несколько мегобайт, после чего 
вылетает с ошибкой. После этого, например, можно просмотреть первае несколько 
секунд фильма, или прослушать первую _часть_  mp3. Вот что говорит:

$ cdrecord -v dev=0,0,0 music.iso
Cdrecord 2.0 (i586-alt-linux-gnu) Copyright (C) 1995-2002 JЖrg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : '_NEC    '
Identifikation : 'CD-RW NR-9300A  '
Revision       : '2.12'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1226752 = 1198 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data   638 MB
Total size:      732 MB (72:35.57) = 326668 sectors
Lout start:      733 MB (72:37/43) = 326668 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Reference speed: 2
  Is not unrestricted
  Is erasable
  ATIP start of lead in:  -11635 (97:26/65)
  ATIP start of lead out: 359849 (79:59/74)
  1T speed low:  0 (reserved val  0) 1T speed high:  4
  2T speed low:  8 2T speed high:  0 (reserved val 10)
  power mult factor: 4 6
  recommended erase/write power: 3
  A1 values: 02 4C B0
  A2 values: 4A C8 36
Disk type:    Phase change
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 33181
Starting to write CD/DVD at speed 4 in real TAO mode for single session.
Last chance to quit, starting real write    0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is OFF.
Performing OPC...
Starting new track at sector: 0
Track 01:    1 of  638 MB written (fifo  96%) [buf  89%] 112.8x.cdrecord: 
Input/output error. write_g1: scsi sendcmd: no error
CDB:  2A 00 00 00 02 6C 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error 
(ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 1.389s timeout 40s

write track data: error after 1269760 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
Writing  time:   11.500s
Average write speed 651.2x.
Fixating...
Fixating time:   62.569s
cdrecord: fifo had 84 puts and 21 gets.
cdrecord: fifo was 0 times empty and 2 times full, min fill was 85%.

Вопрос стандартный. Что делать?

З.Ы. Система Мастер2.2

--
Роман