[Comm] cdrw

[Mike Lykov]

В сообщении от Пятница 16 Май 2003 00:11 Alex Potopaev написал:
> В сообщении от 14 Май 2003 12:29 Mike Lykov писал(a):
>
> ML> вот у меня philips 3210G (CDD5301)
> ML>
> ML> как узнать, поддерживается оно cdrecord или нет?

> А опцию -immed не пробовали? man cdrecord:

> ...This can be  useful  on  broken systems with ATAPI harddisk and
> CD/DVD writer on the same bus  or  with  SCSI  systems  that  don't
> use  disconnect/reconnect.   These  systems  will  freeze while
> blanking or fixating a CD/DVD ...

Попробую.... Но у меня while blanking вовсе не виснет, только во время 
fixating

тем временем принес из дома лог cdrecord (пойдет ниже), а так же посмотрел на 
сайте разработчика cdrecord поддерживаемые дисководы. 
Как я понял, Philips СDD5301 не входит в список определенно работающих с 
версией 2.0 release.... попробую еще с последней альфой 2.01 ;)

Кстати, автор задолбался отвечать на поток тупых писем, о чем прямо написал на 
сайте - "большинство писем либо о железных проблемах, либо о проблемах с ОС, 
либо просто от лени и нечтения доков, и очень редко о проблеме в cdrecord " 
;)

hwconf:

class: CDROM
bus: IDE
detached: 0
device: hdc
driver: ignore
desc: "HITACHI CDR-8130"
-
class: CDROM
bus: SCSI
detached: 0
device: scd0
driver: ignore
desc: "Philips CDD5301"
host: 0
id: 0
channel: 0
lun: 0

лог cdrecord с наиболее подходящим драйвером (по --cdeckdrive)

Calling: /usr/lib/xcdroast/bin/xcdrwrap CDRECORD dev=0,0,0 gracetime=2 
fs=4096k driveropts=burnfree -v -useinfo driver=mmc_cdr speed=1 -dao -eject 
-data "/tmp/track-01.img" ...

scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.24
pregap1: -1
Cdrecord 2.0 (i586-alt-linux-gnu) Copyright (C) 1995-2002 JЖrg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.7'
Driveropts: 'burnfree'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : 'PHILIPS '
Identifikation : 'CDD5301         '
Revision       : 'B1.0'
Device seems to be: Generic mmc2 DVD-ROM.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : MMC-2 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO RAW/R16 RAW/R96R
Drive buf size : 1277952 = 1248 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data   160 MB
Total size:      184 MB (18:18.60) = 82395 sectors
Lout start:      185 MB (18:20/45) = 82395 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Reference speed: 2
Is not unrestricted
Is erasable
ATIP start of lead in:  -11615 (97:27/10)
ATIP start of lead out: 335925 (74:41/00)
1T speed low:  0 (reserved val  0) 1T speed high:  4
2T speed low:  0 (reserved val  5) 2T speed high:  0 (reserved val 12)
power mult factor: 4 5
recommended erase/write power: 3
A1 values: 02 4A B0
A2 values: 5C C6 26
Disk type:    Phase change
Manuf. index: 18
Manufacturer: Plasmon Data systems Ltd.
Blocks total: 335925 Blocks current: 335925 Blocks remaining: 253530
Starting to write CD/DVD at speed 4 in real SAO mode for single session.
Waiting for reader process to fill input buffer ...
input buffer ready.
BURN-Free is ON.
Performing OPC...
Sending CUE sheet...
Writing pregap for track 1 at 82395
Starting new track at sector: 82545

Track 01: Total bytes read/written: 168744960/168744960 (82395 sectors).
Writing  time:  293.045s
Average write speed   3.9x.
Min drive buffer fill was 97%
Fixating...
Fixating time:   70.090s
cdrecord: Input/output error. prevent/allow medium removal: scsi sendcmd: cmd 
timeout after 75.129 (200) s
CDB:  1E 00 00 00 00 00
cmd finished after 75.129s timeout 200s
cdrecord: Input/output error. start/stop unit: scsi sendcmd: cmd timeout after 
75.129 (200) s
CDB:  1B 00 00 00 02 00
cmd finished after 75.129s timeout 200s
cdrecord: fifo had 2658 puts and 2658 gets.
cdrecord: fifo was 0 times empty and 2581 times full, min fill was 93%.

-- 
Mike