smartctl version 5.36 [i586-alt-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST3320620AS Serial Number: 9QF0E8EY Firmware Version: 3.AAE User Capacity: 320 072 933 376 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed May 30 03:18:31 2007 MSD SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 33) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 115) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 111 096 006 Pre-fail Always - 68838999 3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 167 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 18335106 9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 892 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 184 187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Temperature_Celsius 0x0022 061 052 045 Old_age Always - 723779623 194 Temperature_Celsius 0x0022 039 048 000 Old_age Always - 39 (Lifetime Min/Max 0/22) 195 Hardware_ECC_Recovered 0x001a 069 060 000 Old_age Always - 53093289 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 206 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 80 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 80 occurred at disk power-on lifetime: 892 hours (37 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 29 00 00 9a 3c 92 e0 00 08:02:29.013 READ MULTIPLE EXT 29 00 00 9a 3b 92 e0 00 08:02:29.010 READ MULTIPLE EXT 29 00 00 9a 3a 92 e0 00 08:02:29.009 READ MULTIPLE EXT 29 00 00 9a 39 92 e0 00 08:02:29.007 READ MULTIPLE EXT 29 00 00 9a 38 92 e0 00 08:02:29.005 READ MULTIPLE EXT Error 79 occurred at disk power-on lifetime: 892 hours (37 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 29 00 00 1a c4 88 e0 00 08:02:06.414 READ MULTIPLE EXT 29 00 00 1a c3 88 e0 00 08:02:06.442 READ MULTIPLE EXT 29 00 00 1a c2 88 e0 00 08:02:06.439 READ MULTIPLE EXT 29 00 00 1a c1 88 e0 00 08:02:06.438 READ MULTIPLE EXT 29 00 00 1a c0 88 e0 00 08:02:06.436 READ MULTIPLE EXT Error 78 occurred at disk power-on lifetime: 877 hours (36 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 00 00 59 48 a9 e5 00 00:20:18.191 READ MULTIPLE c4 00 00 59 47 a9 e5 00 00:20:18.187 READ MULTIPLE c4 00 00 59 46 a9 e5 00 00:20:18.183 READ MULTIPLE c4 00 00 59 45 a9 e5 00 00:20:18.180 READ MULTIPLE c4 00 00 59 44 a9 e5 00 00:20:18.176 READ MULTIPLE Error 77 occurred at disk power-on lifetime: 877 hours (36 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 29 00 68 42 1d 50 e0 00 00:10:00.466 READ MULTIPLE EXT 29 00 20 22 1d 50 e0 00 00:10:00.466 READ MULTIPLE EXT c4 00 30 9c 2b 7f e2 00 00:10:00.460 READ MULTIPLE c4 00 20 ac a5 8c e1 00 00:10:00.448 READ MULTIPLE c4 00 10 1c a3 8c e1 00 00:10:00.444 READ MULTIPLE Error 76 occurred at disk power-on lifetime: 876 hours (36 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 00 00 16 cb 8f e3 00 00:05:59.927 READ MULTIPLE c4 00 00 16 ca 8f e3 00 00:05:59.925 READ MULTIPLE c4 00 00 16 c9 8f e3 00 00:05:59.918 READ MULTIPLE c4 00 00 16 c8 8f e3 00 00:05:59.915 READ MULTIPLE c4 00 00 16 c7 8f e3 00 00:05:59.912 READ MULTIPLE SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 10% 382 - # 2 Extended offline Interrupted (host reset) 90% 43 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.