[Hardware] [HCL] Foxconn NFPIK8AA-8KERS: 4.0 OK, ALM2.4 -- IDE only
Michael Shigorin
mike на osdn.org.ua
Сб Апр 21 12:30:14 MSD 2007
Здравствуйте.
Вторая железка -- материнская плата Foxconn NFPIK8AA-8EKRS
на NVIDIA nForce Pro 2200/2050 (под 1xOpteron S940 и Reg DDR).
Необычна наличием на борту 8xSATA2 (с дополнительными
контроллерами уже наплавались -- иные создают электромеханические
проблемы класса "chip creep", иные неспособны прокачать поток
данных даже в JBOD с 8+ дисков или через шину, или вообще через
свой CPU -- как Areca). Тут они развешены на две отдельные шины.
Под M24 у нас заводится только IDE (кажется, на ide-generic
и без DMA), SATA/LAN/USB -- ни разу.
Под 4.0-beta взлетело всё (см. приложенный вывод lspci и dmesg).
В итоге не помню каких экспериментов оставил в опциях загрузки
nmi_watchdog=0. Может быть в логах #altlinux за ~20070414.
Слегка дурят сенсоры -- -12V -18.52, M/B Temp -56, CPU Temp с
it8712-isa-0290 выходит +25, хотя по k8temp-pci-00c3 -- +38).
NCQ нет:
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
Слот PCI (32/33) -- один, остальное -- PCIE. Жаль, что хоть
какого-то встроенного видео не положили, зато два Gigabit
Ethernet.
ECC DDR266 съело (в двухканальном режиме); и здесь
в bluesmoke.sourceforge.net пока (if ever) не игрался.
Из остального вкратце: вообще-то оно ориентировано явно на
рабочую станцию, начиная с SLI PCIEx16 и заканчивая одним
свободным fan head, расположенным около задней панели, а не
ближе к фронтальным пропеллерам; ещё есть FireWire-800 и
S/PDIF (оптика/медь). :-)
То, что полкоробки занимают все возможные кабели и шлейфы --
вплоть до четырёх сдвоенных переходов с molex на SATA Power
-- приятно.
Толковый обзор тут:
http://www.lostcircuits.com/motherboard/foxconn_nfpik8aa/
Менее толковый (по 3D-части на инженерном образце; по крайней
мере описания на плате с тех пор добавились):
http://www.ixbt.com/mainboard/foxconn/foxconn-nfpik8aa-8ekrs-nforce4pro.shtml
Из проблем на сейчас наблюдается заметный LA при операциях
с новосозданным RAID5, но это больше похоже на нюансы с его
созданием (разбивать надо было так, чтобы размер предыдущего
раздела в fdisk -l был без "+" в конце -- бишь выровненный на
границу в 63 сектора, что ли; возможно, придётся как-нибудь
перебить, поскольку избежать всей этой мороки и использовать
целые диски в RAID в данном разе не получается).
PS: сейчас по результатам повторного обгугливания в sysadmins@
ссылки черкну и на f.i уложил.
--
---- WBR, Michael Shigorin <mike at altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
-------------- next part --------------
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev a2)
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3)
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3)
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:06.0 VGA compatible controller: S3 Inc. 86c775/86c785 [Trio 64V2/DX or /GX] (rev 04)
01:07.0 FireWire (IEEE 1394): Texas Instruments TSB82AA2 IEEE-1394b Link Layer Controller (rev 01)
80:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
80:01.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
80:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3)
80:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3)
80:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
80:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
80:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
-------------- next part --------------
Bootdata ok (command line is auto BOOT_IMAGE=ALTLinux ro root=UUID=77fdad11-19e2-483d-8e6d-8a200349eb51 nmi_watchdog=0 panic=300)
Linux version 2.6.18-ovz-smp-alt13 (builder at hint1.office.altlinux.org) (gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt11)) #1 SMP Mon Apr 9 01:42:31 MSD 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c000 (usable)
BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7970
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff30c0
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fffb180
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fffb0c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003fff0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003fff0000
On node 0 totalpages: 256810
DMA zone: 2809 pages, LIFO batch:0
DMA32 zone: 254001 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:5 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xdffff000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 17, address 0xdffff000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Built 1 zonelists. Total pages: 256810
Kernel command line: auto BOOT_IMAGE=ALTLinux ro root=UUID=77fdad11-19e2-483d-8e6d-8a200349eb51 nmi_watchdog=0 panic=300
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2009.288 MHz processor.
Console: colour VGA+ 80x43
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ 81c2000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1025492k/1048512k available (1910k kernel code, 22620k reserved, 1207k data, 220k init)
Calibrating delay using timer specific routine.. 4021.03 BogoMIPS (lpj=8042061)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
Freeing SMP alternatives: 28k freed
Page beancounter hash is 65536 entries.
checking if image is initramfs... it is
Freeing initrd memory: 498k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist.
Using local APIC timer interrupts.
result 12558067
Detected 12.558 MHz APIC timer.
Brought up 1 CPUs
testing NMI watchdog ... CPU#0: NMI appears to be stuck (0->0)!
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
PCI: No mmconfig possible on device 0:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:06.0
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Root Bridge [PCI1] (0000:80)
PCI: Probing PCI hardware (bus 80)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Interrupt Link [APC1] (IRQs *40), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *41), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *42), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *43), disabled.
ACPI: PCI Interrupt Link [SLMA] (IRQs 44 45 46 47) *0, disabled.
ACPI: PCI Interrupt Link [SLS1] (IRQs 44 45 46 47) *0, disabled.
ACPI: PCI Interrupt Link [SLS2] (IRQs 44 45 46 47) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling IOMMU.
pnp: 00:00: ioport range 0x1000-0x107f could not be reserved
pnp: 00:00: ioport range 0x1080-0x10ff has been reserved
pnp: 00:00: ioport range 0x1400-0x147f has been reserved
pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:00: ioport range 0x1800-0x187f has been reserved
pnp: 00:00: ioport range 0x1880-0x18ff has been reserved
PCI: Bridge: 0000:00:09.0
IO window: a000-afff
MEM window: f4000000-fbffffff
PREFETCH window: fea00000-feafffff
PCI: Bridge: 0000:00:0c.0
IO window: 9000-9fff
MEM window: fe900000-fe9fffff
PREFETCH window: fe800000-fe8fffff
PCI: Bridge: 0000:00:0d.0
IO window: 8000-8fff
MEM window: fe700000-fe7fffff
PREFETCH window: fe600000-fe6fffff
PCI: Bridge: 0000:00:0e.0
IO window: 7000-7fff
MEM window: fe500000-fe5fffff
PREFETCH window: fe400000-fe4fffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Bridge: 0000:80:0d.0
IO window: 3000-3fff
MEM window: dfe00000-dfefffff
PREFETCH window: dfd00000-dfdfffff
PCI: Bridge: 0000:80:0e.0
IO window: 2000-2fff
MEM window: dfc00000-dfcfffff
PREFETCH window: dfb00000-dfbfffff
PCI: Setting latency timer of device 0000:80:0d.0 to 64
PCI: Setting latency timer of device 0000:80:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1176739846.464:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Found HT MSI mapping on 0000:00:0c.0 with capability disabled
PCI: Found HT MSI mapping on 0000:00:00.0 with capability enabled
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Found HT MSI mapping on 0000:00:0d.0 with capability disabled
PCI: Found HT MSI mapping on 0000:00:00.0 with capability enabled
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Found HT MSI mapping on 0000:00:0e.0 with capability disabled
PCI: Found HT MSI mapping on 0000:00:00.0 with capability enabled
PCI: Linking AER extended capability on 0000:00:0e.0
PCI: Found HT MSI mapping on 0000:80:0d.0 with capability disabled
PCI: Found HT MSI mapping on 0000:80:00.0 with capability disabled
PCI: MSI quirk detected. MSI disabled on chipset 0000:80:0d.0.
PCI: Found HT MSI mapping on 0000:80:0e.0 with capability disabled
PCI: Found HT MSI mapping on 0000:80:00.0 with capability disabled
PCI: MSI quirk detected. MSI disabled on chipset 0000:80:0e.0.
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie01]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie01]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie01]
Allocate Port Service[0000:00:0e.0:pcie03]
PCI: Setting latency timer of device 0000:80:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:80:0d.0:pcie00]
Allocate Port Service[0000:80:0d.0:pcie01]
Allocate Port Service[0000:80:0d.0:pcie03]
PCI: Setting latency timer of device 0000:80:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:80:0e.0:pcie00]
Allocate Port Service[0000:80:0e.0:pcie01]
Allocate Port Service[0000:80:0e.0:pcie03]
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
Freeing unused kernel memory: 220k freed
Executing init=/init
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 162
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xe800-0xe807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe808-0xe80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide0...
Probing IDE interface ide1...
SCSI subsystem initialized
libata version 2.00 loaded.
sata_nv 0000:00:07.0: version 2.0
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
GSI 16 sharing vector 0xE1 and IRQ 16
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD400 irq 225
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD408 irq 225
scsi0 : sata_nv
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: Hitachi HDT72503 Rev: V54O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: Hitachi HDT72503 Rev: V54O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: Attached scsi disk sdb
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
GSI 17 sharing vector 0xE9 and IRQ 17
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC000 irq 233
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC008 irq 233
scsi2 : sata_nv
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/133
scsi3 : sata_nv
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/133
Vendor: ATA Model: Hitachi HDT72503 Rev: V54O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: sdc1 sdc2 sdc3
sd 2:0:0:0: Attached scsi disk sdc
Vendor: ATA Model: Hitachi HDT72503 Rev: V54O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
sdd: sdd1 sdd2 sdd3
sd 3:0:0:0: Attached scsi disk sdd
ACPI: PCI Interrupt Link [SLS1] enabled at IRQ 47
GSI 18 sharing vector 0x32 and IRQ 18
ACPI: PCI Interrupt 0000:80:07.0[A] -> Link [SLS1] -> GSI 47 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:80:07.0 to 64
ata5: SATA max UDMA/133 cmd 0x6C00 ctl 0x6802 bmdma 0x5C00 irq 50
ata6: SATA max UDMA/133 cmd 0x6400 ctl 0x6002 bmdma 0x5C08 irq 50
scsi4 : sata_nv
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata5.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata5.00: ata5: dev 0 multi count 16
ata5.00: configured for UDMA/133
scsi5 : sata_nv
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata6.00: ata6: dev 0 multi count 16
ata6.00: configured for UDMA/133
Vendor: ATA Model: HDT722525DLA380 Rev: V44O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sde: 488397168 512-byte hdwr sectors (250059 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
SCSI device sde: 488397168 512-byte hdwr sectors (250059 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
sde: sde1 sde2 sde3
sd 4:0:0:0: Attached scsi disk sde
Vendor: ATA Model: HDT722525DLA380 Rev: V44O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
sdf: sdf1 sdf2 sdf3
sd 5:0:0:0: Attached scsi disk sdf
ACPI: PCI Interrupt Link [SLS2] enabled at IRQ 46
GSI 19 sharing vector 0x3A and IRQ 19
ACPI: PCI Interrupt 0000:80:08.0[A] -> Link [SLS2] -> GSI 46 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:80:08.0 to 64
ata7: SATA max UDMA/133 cmd 0x5800 ctl 0x5402 bmdma 0x4800 irq 58
ata8: SATA max UDMA/133 cmd 0x5000 ctl 0x4C02 bmdma 0x4808 irq 58
scsi6 : sata_nv
ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata7.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata7.00: ata7: dev 0 multi count 16
ata7.00: configured for UDMA/133
scsi7 : sata_nv
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata8.00: ATA-7, max UDMA/133, 488395055 sectors: LBA48 NCQ (depth 0/32)
ata8.00: ata8: dev 0 multi count 16
ata8.00: configured for UDMA/133
Vendor: ATA Model: HDT722525DLA380 Rev: V44O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdg: 488397168 512-byte hdwr sectors (250059 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
SCSI device sdg: 488397168 512-byte hdwr sectors (250059 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
sdg: sdg1 sdg2 sdg3
sd 6:0:0:0: Attached scsi disk sdg
Vendor: ATA Model: HDT722525DLA380 Rev: V44O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdh: 488395055 512-byte hdwr sectors (250058 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: drive cache: write back
SCSI device sdh: 488395055 512-byte hdwr sectors (250058 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: drive cache: write back
sdh: sdh1 sdh2 sdh3
sd 7:0:0:0: Attached scsi disk sdh
md: raid1 personality registered for level 1
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdh3 ...
md: adding sdh3 ...
md: sdh2 has different UUID to sdh3
md: adding sdg3 ...
md: sdg2 has different UUID to sdh3
md: adding sdf3 ...
md: sdf2 has different UUID to sdh3
md: adding sde3 ...
md: sde2 has different UUID to sdh3
md: sdd3 has different UUID to sdh3
md: sdd2 has different UUID to sdh3
md: sdc3 has different UUID to sdh3
md: sdc2 has different UUID to sdh3
md: sdb3 has different UUID to sdh3
md: sdb2 has different UUID to sdh3
md: sda3 has different UUID to sdh3
md: sda2 has different UUID to sdh3
md: created md0
md: bind<sde3>
md: bind<sdf3>
md: bind<sdg3>
md: bind<sdh3>
md: running: <sdh3><sdg3><sdf3><sde3>
md: personality for level 5 is not loaded!
md: do_md_run() returned -22
md: md0 stopped.
md: unbind<sdh3>
md: export_rdev(sdh3)
md: unbind<sdg3>
md: export_rdev(sdg3)
md: unbind<sdf3>
md: export_rdev(sdf3)
md: unbind<sde3>
md: export_rdev(sde3)
md: considering sdh2 ...
md: adding sdh2 ...
md: sdg2 has different UUID to sdh2
md: adding sdf2 ...
md: sde2 has different UUID to sdh2
md: sdd3 has different UUID to sdh2
md: sdd2 has different UUID to sdh2
md: sdc3 has different UUID to sdh2
md: sdc2 has different UUID to sdh2
md: sdb3 has different UUID to sdh2
md: sdb2 has different UUID to sdh2
md: sda3 has different UUID to sdh2
md: sda2 has different UUID to sdh2
md: created md1
md: bind<sdf2>
md: bind<sdh2>
md: running: <sdh2><sdf2>
raid1: raid set md1 active with 2 out of 2 mirrors
md: considering sdg2 ...
md: adding sdg2 ...
md: adding sde2 ...
md: sdd3 has different UUID to sdg2
md: sdd2 has different UUID to sdg2
md: sdc3 has different UUID to sdg2
md: sdc2 has different UUID to sdg2
md: sdb3 has different UUID to sdg2
md: sdb2 has different UUID to sdg2
md: sda3 has different UUID to sdg2
md: sda2 has different UUID to sdg2
md: created md2
md: bind<sde2>
md: bind<sdg2>
md: running: <sdg2><sde2>
raid1: raid set md2 active with 2 out of 2 mirrors
md: considering sdd3 ...
md: adding sdd3 ...
md: sdd2 has different UUID to sdd3
md: adding sdc3 ...
md: sdc2 has different UUID to sdd3
md: adding sdb3 ...
md: sdb2 has different UUID to sdd3
md: adding sda3 ...
md: sda2 has different UUID to sdd3
md: created md4
md: bind<sda3>
md: bind<sdb3>
md: bind<sdc3>
md: bind<sdd3>
md: running: <sdd3><sdc3><sdb3><sda3>
md: personality for level 5 is not loaded!
md: do_md_run() returned -22
md: md4 stopped.
md: unbind<sdd3>
md: export_rdev(sdd3)
md: unbind<sdc3>
md: export_rdev(sdc3)
md: unbind<sdb3>
md: export_rdev(sdb3)
md: unbind<sda3>
md: export_rdev(sda3)
md: considering sdd2 ...
md: adding sdd2 ...
md: adding sdc2 ...
md: adding sdb2 ...
md: adding sda2 ...
md: created md3
md: bind<sda2>
md: bind<sdb2>
md: bind<sdc2>
md: bind<sdd2>
md: running: <sdd2><sdc2><sdb2><sda2>
raid1: raid set md3 active with 4 out of 4 mirrors
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: Attached scsi generic sg3 type 0
sd 4:0:0:0: Attached scsi generic sg4 type 0
sd 5:0:0:0: Attached scsi generic sg5 type 0
sd 6:0:0:0: Attached scsi generic sg6 type 0
sd 7:0:0:0: Attached scsi generic sg7 type 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
GSI 20 sharing vector 0x42 and IRQ 20
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 66, io mem 0xfebff000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
GSI 21 sharing vector 0x4A and IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 74, io mem 0xfebfe000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
input: PC Speaker as /class/input/input0
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ieee1394: Initialized config rom entry `ip1394'
eth0: forcedeth.c: subsystem: 0105b:0ca5 bound to 0000:00:0a.0
ACPI: PCI Interrupt Link [SLMA] BIOS reported IRQ 47, using IRQ 45
ACPI: PCI Interrupt Link [SLMA] enabled at IRQ 45
GSI 22 sharing vector 0x52 and IRQ 22
ACPI: PCI Interrupt 0000:80:0a.0[A] -> Link [SLMA] -> GSI 45 (level, low) -> IRQ 82
PCI: Setting latency timer of device 0000:80:0a.0 to 64
forcedeth: using HIGHDMA
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 23 sharing vector 0x5A and IRQ 23
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 90
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[90] MMIO=[fbfff000-fbfff7ff] Max Packet=[2] IR/IT contexts=[4/8]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to setting max_packet_size to 512 bytes
eth1: forcedeth.c: subsystem: 0105b:0ca5 bound to 0000:80:0a.0
Adding 265032k swap on /dev/sda1. Priority:50 extents:1 across:265032k
Adding 265032k swap on /dev/sdb1. Priority:50 extents:1 across:265032k
Adding 265032k swap on /dev/sdc1. Priority:50 extents:1 across:265032k
Adding 265032k swap on /dev/sdd1. Priority:50 extents:1 across:265032k
EXT3 FS on md3, internal journal
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00016c20000b1227]
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel at redhat.com
md: md0 stopped.
md: bind<sde3>
md: bind<sdh3>
md: bind<sdg3>
md: bind<sdf3>
raid5: automatically using best checksumming function: generic_sse
generic_sse: 6443.000 MB/sec
raid5: using function: generic_sse (6443.000 MB/sec)
raid6: int64x1 1772 MB/s
raid6: int64x2 2257 MB/s
raid6: int64x4 1713 MB/s
raid6: int64x8 1761 MB/s
raid6: sse2x1 2602 MB/s
raid6: sse2x2 3456 MB/s
raid6: sse2x4 3647 MB/s
raid6: using algorithm sse2x4 (3647 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: device sdf3 operational as raid disk 0
raid5: device sdg3 operational as raid disk 3
raid5: device sdh3 operational as raid disk 2
raid5: device sde3 operational as raid disk 1
raid5: allocated 4262kB for md0
raid5: raid level 5 set md0 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4 fd:0
disk 0, o:1, dev:sdf3
disk 1, o:1, dev:sde3
disk 2, o:1, dev:sdh3
disk 3, o:1, dev:sdg3
md: md4 stopped.
md: bind<sdb3>
md: bind<sdc3>
md: bind<sdd3>
md: bind<sda3>
raid5: device sda3 operational as raid disk 0
raid5: device sdd3 operational as raid disk 3
raid5: device sdc3 operational as raid disk 2
raid5: device sdb3 operational as raid disk 1
raid5: allocated 4262kB for md4
raid5: raid level 5 set md4 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4 fd:0
disk 0, o:1, dev:sda3
disk 1, o:1, dev:sdb3
disk 2, o:1, dev:sdc3
disk 3, o:1, dev:sdd3
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
Filesystem "md4": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md4
Ending clean XFS mount for filesystem: md4
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with journal data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
it87: Found IT8712F chip at 0x290, revision 6
it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 312 bytes per conntrack
input: AT Translated Set 2 keyboard as /class/input/input1
Подробная информация о списке рассылки Hardware