$ dmesg 
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.25-std-def-alt10 (builder@apiary.egro.altlinux.org) (gcc version 4.1.2 20070626 (ALT Linux, build 4.1.2-alt3)) #1 SMP Sat Oct 11 09:47:26 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fe30000 (usable)
 BIOS-e820: 000000003fe30000 - 000000003fe3e6d5 (ACPI NVS)
 BIOS-e820: 000000003ff10000 - 000000003ff30000 (reserved)
 BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
 BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
 BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
126MB HIGHMEM available.
896MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00ff780] 000ff780
Entering add_active_range(0, 0, 261680) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   261680
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   261680
On node 0 totalpages: 261680
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 252 pages used for memmap
  HighMem zone: 32052 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F62C0, 0014 (r0 ACPIAM)
ACPI: RSDT 3FF30000, 0034 (r1 INTEL  D865PERL 20050213 MSFT       97)
ACPI: FACP 3FF30200, 0081 (r2 INTEL  D865PERL 20050213 MSFT       97)
ACPI: DSDT 3FF30370, 4272 (r1 INTEL  D865PERL        6 MSFT  100000D)
ACPI: FACS 3FF40000, 0040
ACPI: APIC 3FF30300, 0068 (r1 INTEL  D865PERL 20050213 MSFT       97)
ACPI: ASF! 3FF345F0, 0099 (r16 LEGEND I865PASF        1 MSFT  100000D)
ACPI: WDDT 3FF34689, 0040 (r1 INTEL  OEMWDDT         1 MSFT  100000D)
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:becf0000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259636
Kernel command line: auto BOOT_IMAGE=ALTLinux ro root=UUID=48682762-5d99-483f-a737-0c7452ca988c resume=/dev/sda1 panic=30 splash=silent
bootsplash: silent mode.
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2793.163 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1031972k/1046720k available (2295k kernel code, 14180k reserved, 1051k data, 392k init, 129216k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe13000 - 0xfffff000   (1968 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc054d000 - 0xc05af000   ( 392 kB)
      .data : 0xc043dc7f - 0xc0544ba0   (1051 kB)
      .text : 0xc0200000 - 0xc043dc7f   (2295 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay using timer specific routine.. 5591.58 BogoMIPS (lpj=11183174)
Security Framework initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03
Booting processor 1/1 ip 4000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5586.49 BogoMIPS (lpj=11172989)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03
Total of 2 processors activated (11178.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=180 bytes
sizeof(task_struct)=3728 bytes
CPU0 attaching sched-domain:
 domain 0: span 00000003
  groups: 00000001 00000002
  domain 1: span 00000003
   groups: 00000003
CPU1 attaching sched-domain:
 domain 0: span 00000003
  groups: 00000002 00000001
  domain 1: span 00000003
   groups: 00000003
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
system 00:06: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x400-0x47f has been reserved
system 00:08: ioport range 0x680-0x6ff has been reserved
system 00:08: ioport range 0x500-0x53f has been reserved
system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:08: iomem range 0xfed20000-0xfed9ffff could not be reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0xc0000-0xd7fff could not be reserved
system 00:09: iomem range 0xe0000-0xfffff could not be reserved
system 00:09: iomem range 0x100000-0x3fffffff could not be reserved
system 00:09: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: a000-afff
  MEM window: 0xff800000-0xff8fffff
  PREFETCH window: 0x00000000e8000000-0x00000000f7ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: b000-bfff
  MEM window: 0xff900000-0xff9fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 721k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1226315021.408:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
vesafb: framebuffer at 0xe8000000, mapped to 0xf8880000, using 3750k, total 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=16
vesafb: protected mode interface info at c000:579f
vesafb: pmi: set display start = c00c5833, set palette = c00c587f
vesafb: pmi: ports = a810 a816 a854 a838 a83c a85c a800 a804 a8b0 a8b2 a8b4 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 133202 bytes
bootsplash: ...found (800x600, 12886 bytes, v3).
Console: switching to colour frame buffer device 97x34
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 392k freed
Write protecting the kernel read-only data: 860k
Executing init=/init
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
No dock devices found.
ICH5: IDE controller (0x8086:0x24db rev 0x02) at  PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:PIO, hdb:PIO
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:PIO
Probing IDE interface ide0...
SCSI subsystem initialized
libata version 3.00 loaded.
Probing IDE interface ide1...
hdc: Optiarc DVD RW AD-7170A, ATAPI CD/DVD-ROM drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/66 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ata_piix 0000:00:1f.2: version 2.12
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xec00 ctl 0xe800 bmdma 0xdc00 irq 18
ata2: SATA max UDMA/133 cmd 0xe400 ctl 0xe000 bmdma 0xdc08 irq 18
ata2.00: HPA detected: current 234435439, native 234441648
ata2.00: ATA-6: ST3120827AS, 3.42, max UDMA/133
ata2.00: 234435439 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      ST3120827AS      3.42 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] 234435439 512-byte hardware sectors (120031 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 234435439 512-byte hardware sectors (120031 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 1:0:0:0: [sda] Attached SCSI disk
Probing IDE interface ide0...
PM: Starting manual resume from disk
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /devices/platform/pcspkr/input/input1
sd 1:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux agpgart interface v0.103
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa00000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25-std-def-alt10 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
agpgart: Detected an Intel 865 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000cc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25-std-def-alt10 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 1-0:1.0: unable to enumerate USB device on port 1
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: ACPI0007:01 is registered as cooling_device1
ACPI: Processor [CPU2] (supports 8 throttling states)
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25-std-def-alt10 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
hub 1-0:1.0: unable to enumerate USB device on port 3
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.25-std-def-alt10 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
ACPI: Sleep Button (CM) [SLPB]
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.25-std-def-alt10 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:02:03.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:02:03.0: Try the "8139too" driver instead.
hub 1-0:1.0: unable to enumerate USB device on port 4
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xf8d68000, 00:30:84:76:12:b1, IRQ 19
eth0:  Identified 8139 chip type 'RTL-8139C'
usb 1-5: new high speed USB device using ehci_hcd and address 5
usb 1-5: configuration #1 chosen from 1 choice
usb 1-5: New USB device found, idVendor=1005, idProduct=b113
usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-5: Product: USB FLASH DRIVE 
usb 1-5: Manufacturer:         
usb 1-5: SerialNumber: 197218000254
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: New USB device found, idVendor=046d, idProduct=c018
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB Optical Mouse
usb 2-1: Manufacturer: Logitech
intel8x0_measure_ac97_clock: measured 55229 usecs
intel8x0: clocking to 48000
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=0566, idProduct=3107
usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-2: new full speed USB device using uhci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usb 3-2: New USB device found, idVendor=046d, idProduct=08da
usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input4
input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-1
input: HID 0566:3107 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input5
input,hidraw1: USB HID v1.10 Keyboard [HID 0566:3107] on usb-0000:00:1d.1-1
input: HID 0566:3107 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input6
input,hidraw2: USB HID v1.10 Device [HID 0566:3107] on usb-0000:00:1d.1-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Linux video capture interface: v2.00
gspca: main v2.3.0 registered
usbcore: registered new interface driver snd-usb-audio
gspca: probing 046d:08da
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access              USB FLASH DRIVE  34CD PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sdb] 2007040 512-byte hardware sectors (1028 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 2007040 512-byte hardware sectors (1028 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
zc3xx: probe 2wr ov vga 0x0000
zc3xx: probe sensor -> 11
zc3xx: Find Sensor HV7131R(c)
gspca: probe ok
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver zc3xx
zc3xx: registered
Adding 1020116k swap on /dev/sda1.  Priority:-1 extents:1 across:1020116k
EXT3 FS on sda2, internal journal
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!